Material Safety Data Sheet

NOCO SBMV ATF


Section I - Chemical Property and Company Information


Manufacturer's Name NOCO Energy Corp.
Manufacturer's Address 2440 Sheridan Dr., Tonawanda, NY 14150
Telephone 1-800-544-1846
Emergency Phone Number 1-800-424-9300 (Chemtrec)
Product Name NOCO SBMV ATF
Product Code NOC1872
Chemical Name and Synonym Petroleum Hydrocarbon Plus Additives
Product Use Automatic Transmission Fluid

Section II - Hazardous Ingredients / Identity Information


Hazardous Components
CAS Number
%
PEL (OSHA)
TLV (ACGIH)

Aliphatic Petroleum Distillates

64742-65-0
83
5 mg/m³ TWA oil mist
5 mg/m³ oil mist
Additives
Proprietary
17
5 mg/m³ TWA oil mist
5 mg/m³ oil mist
WHMIS
Not Controlled
     

Section III - Physical / Chemical Characteristics


Boiling Point Not Determined (High)
Specific Gravity 0.875 @ 60°F
Vapor Pressure @ 20° C < 0.0001 mm Hg
Vapor Density 10+
Solubility in Water Insoluble, Nil
Appearance and Odor Red Liquid, Slight Odor (petroleum)
Freezing Point N/A

Section IV - Fire and Explosion Data


Flashpoint >193°C (380°F)
Method Used COC
Flammable Limits in air % by volume N/A
Auto-Ignition Temp 675°F, 359°C
Extinguisher Media Carbon dioxide, Dry chemical, Foam, Water fog
Special Fire Fighting Procedures Use water fog, dry chemical, foam or carbon dioxide. Water fog should be used to keep fire exposed containers cool. Do not point solid water stream directly into burning oil to avoid spreading.
National Fire Protection Association (NFPA) Health: 1 Flammability: 1 Reactivity: 0  

Section V - Physical Hazards (Reactivity Data)


Stability Stable
Conditions to Avoid Contact with heat, sparks, flame and all sources of ignition.
Incompatibility Strong acids, bases and oxidizing agents.
Hazardous Decomposition Products Carbon Oxides, various hydrocarbons
Hazardous Polymerization Will not occur

Section VI - Health Hazards


Signs and Symptoms of Exposure:  
  Eyes This material is classified as a minor eye irritant.
  Skin Absorption No acute effects known
  Skin Contact This material may cause moderate irritation with prolonged or repeated contact.
  Inhalation No Effects Expected.
  Ingestion Low toxicity. Material is not expected to be a problem when ingested.
  Chronic Effects None known
     
Emergency and First Aid Procedures
  Eyes Flush with large amounts of cold water for at least 15 minutes. Do not let victim rub eyes. If irritation develops, contact a physician immediately.
  Skin Wash affected area with soap and water. Do not reuse clothing soaked with this product until laundered. Discard all leather articles which have been soaked with this product. If irritation develops, contact a physician immediately.
  Inhalation If inhaled, move to fresh air. If victim has stopped breathing give artificial respiration, preferably, mouth to mouth. Contact a physician immediately.
  Ingestion

Do not induce vomiting. If vomiting occurs spontaneously, keep head below the hips to prevent aspiration of material into the lungs. If individual is conscious, administer milk or water to dilute stomach contents. Contact a physician immediately. Small amounts which accidentally enter the mouth should be rinsed out until the taste of it is gone.


Section VI - Special Precautions / Spill & Leak Procedures


Handling Avoid getting this material in contact with your skin and eyes. Avoid the generation of oil mists. Wash hands after handling and before eating. Avoid container damage while handling.
Storage Store in closed containers in a cool, dry well ventilated area. Keep this product away from open flames, sources of heat and ignition sources. Store at temperatures below 60ºC (140ºF).
Spill & Leak Response Do not allow spilled material to enter sewers or streams. For a small spill, add dry material (such as diatomaceous earth, dry clay or sand) to absorb (if large spill, dike to contain). Using recommended protective equipment, pick up bulk of spill and containerize for recovery or disposal. Flush area with water to remove residues.
Waste Disposal All recovered material should be packaged, labeled, transported and disposed or reclaimed in conformance with Good Engineering Practices. Comply with all applicable governmental regulations. Avoid land filling of liquids. Reclaim where possible.

Section VIII - Special Protection Information


Respiratory Protection If oil mists are generated, observe the OSHA exposure limit of 5 mg/m³. If workplace exposure limit is exceeded, use NIOSH approved respirator (either a disposable dust/mist mask breathing apparatus or supplied-air respirator depending upon conditions) for entry into confined space in the absence of proper environmental control.
Protective Gloves Wear protective gloves. The following glove materials are acceptable: polyvinyl chloride, neoprene, nitrile, polyvinyl alcohol and viton.
Eye Protection Chemical goggles or a full face shield. Do not wear contact lenses.
Other Protective Wear Wear impervious, protective clothing including rubber safety shoes to avoid prolonged or repeated skin contact. The following materials are acceptable as protective clothing materials: polyvinyl alcohol, polyvinyl chloride, neoprene, nitrile, viton and polyurethane.

Section IX - DOT Additional Regulatory Information


  DOT    
  Proper Shipping Name Not Regulated  
  Hazard Class Not Regulated  
  ID Number Not Regulated  
  Label Required Not Regulated  
  IMDG Proper Shipping Name Not a dangerous good  
  IATA Proper Shipping Name Not a dangerous good  
  Regulatory Information    
  TSCA (Toxic Substance Control Act) This material is in compliance with the TOXIC SUBSTANCES CONTROL ACT (15 USC 2601-2629) and is listed in the TSCA Inventory.  
 

SARA 302 Threshold Planning Quantity, N/A
SARA 304 Reportable Quantity, N/A
SARA 311/312 Reporting:

 
    Health Immediate (Acute) Yes
    Health Delayed (Chronic) No
    Physical Fire No
    Physical Sudden Release of Pressure No
         

Section X - Additional Information


Prepared By Tom Goodnight
Phone number of Preparer 1-800-500-6626
Date Prepared 06/09/2006
Revised Date 06/01/2011

Disclaimer


Information presented herein has been compiled from information provided to us by our suppliers and other sources considered to be dependable and is accurate and reliable to the best of our knowledge. Nothing herein is to be construed as recommending any practice or the use of any product in violation of any patent or in violation of any law or regulation. It is the users' responsibility to determine the suitability of any material for a specific purpose and to adopt such safety precautions as may be necessary. We make no warranty as to the results to be obtained in using any material and since conditions of use are not under our control, we must necessarily disclaim all liability with respect to the use of any material supplied by us.